Learn to Crochet a Cute Egg Beret!

Learn to Crochet a Cute Egg Beret!

Table of Contents

1. Introduction
2. Materials Needed
3. Magic Circle
4. Round 1: Double Crocheting
5. Round 2: Increasing Stitches
6. Round 3: More Increases
7. Rounds 4-9: Continuing the Pattern
8. Rounds 10-14: Without Increases
9. Rounds 15-16: Decreasing Stitches
10. Measuring and Finishing the Beret
11. Adding the Ribbing Band
12. Creating the Yoke
13. Sewing the Yoke to the Beret
14. Conclusion
15. FAQ

Introduction

Creating your own beret can be a fun and rewarding project, especially for beginners. In this tutorial, we will guide you through the step-by-step process of making a cute egg beret. With just a few materials and some basic crochet techniques, you'll be able to create your own stylish accessory. So grab your crochet hook and let's get started!

Materials Needed

Before we begin, make sure you have the following materials on hand:

• Yarn (preferably a soft acrylic or wool blend)
• Crochet hook (size H/5.00mm)
• Scissors
• Yarn needle

Magic Circle

To start your beret, we will begin by creating a magic circle. This technique allows you to create an adjustable ring that will serve as the foundation for your stitches. Follow these steps to create a magic circle:

1. Wrap the yarn around your two fingers, forming an "X."
2. Insert your crochet hook under the first strand of yarn and scoop the farthest strand into that first strand.
3. Twist your hook to create a loop.
4. Slowly remove the loop from your fingers and yarn over.
5. Pull the yarn through the loop to create a slip stitch.

Congratulations, you have now created a magic circle!

Round 1: Double Crocheting

For the first round of your beret, we will be double crocheting. If you are unfamiliar with this stitch, please refer to our tutorial on how to double crochet. In this round, you will double crochet 10 stitches into the magic circle, creating the initial ring of your beret. Once you have completed all 10 stitches, pull the shorter strand of yarn to close the loop. Your first round is now complete.

Round 2: Increasing Stitches

In the second round, we will be increasing the number of stitches. To do this, you will put two double crochets in one stitch, which is called an increase. Repeat this increase throughout the entire round. By the end of this round, you should have a total of 20 stitches.

Round 3: More Increases

For the third round, you will continue with the pattern of adding one double crochet and then an increase. Repeat this pattern throughout the entire round. By the end, you should have a total of 30 stitches.

Rounds 4-9: Continuing the Pattern

In rounds 4-9, you will repeat the pattern of placing one double crochet on each stitch and then increasing after every two double crochets. This pattern will create a gradual expansion of your beret. Repeat the pattern of two double crochets and then an increase for a total of nine times in each round. By the end of round 9, you should have 40 stitches.

Rounds 10-14: Without Increases

For rounds 10-14, you will continue double crocheting without any increases. This will help maintain the size of your beret. These rounds will serve as the middle section of your beret. There should still be 40 stitches in each round at the end.

Rounds 15-16: Decreasing Stitches

In rounds 15-16, you will start decreasing the number of stitches to create the top portion of the beret. To decrease, you will double crochet on the first few stitches and then decrease on the next stitch. Repeat this pattern throughout the rounds, gradually decreasing the number of stitches. By the end of round 16, you should have 80 stitches left.

Measuring and Finishing the Beret

Once you have completed the 16 rounds of crocheting, it's time to measure your beret. Lay it flat and ensure that all sides are equal. The diameter of the opening should be about 7.5 to 7 inches. Adjust the size if necessary.

To finish the beret, do a slip stitch on the next stitch, leaving a long tail for sewing. When wearing the beret, make sure it is slightly loose on your head, allowing enough room for the ribbing band.

Adding the Ribbing Band

To create the ribbing band, chain until you have a width of 1 inch. Skip a stitch and then single crochet on the remaining stitches. Flip your work and single crochet on the back loops of the first stitches. Repeat this pattern for several rows, occasionally measuring to ensure the band fits the crown of your head properly. The final measurements of the band should be 1 inch in width and 18.5 inches in length.

Sew the band together to form a circle. Align it with the opening of the beret and start sewing. Insert your needle underneath the beret and over the band, alternating back and forth until the band is securely attached.

Creating the Yoke

For the yoke, start with a magic circle and half double crochet on the circle. This stitch will give the yoke a textured look. Continue increasing on each stitch in half double crochet for the second round. By the end, you should have 12 stitches.

Sewing the Yoke to the Beret

Align the yoke with the center of the beret and sew it on. Use your yarn needle to insert the needle underneath the beret and over the yoke, securing it in place. Make sure the yoke is centered and even on all sides.

Conclusion

Congratulations! You have successfully completed your cute egg beret. We hope this tutorial has been helpful and that you enjoyed creating your own beret. Feel free to tag us in your beret creations and don't forget to always create with a smile. Happy crocheting!

FAQ

Q: Can I use a different yarn weight for this pattern? A: Yes, you can experiment with different yarn weights to achieve different results. Just make sure to adjust your crochet hook size accordingly.

Q: How can I make the beret smaller or larger? A: To make the beret smaller, you can use a smaller crochet hook or reduce the number of rounds with increases. To make it larger, you can use a larger crochet hook or add more rounds with increases.

Q: Can I customize the ribbing band? A: Absolutely! You can make the ribbing band wider or narrower by adjusting the number of chains at the beginning. You can also use a different stitch pattern for the ribbing, such as ribbing or seed stitch.

Q: Can I add embellishments to my beret? A: Definitely! Feel free to get creative and add embellishments like flowers, buttons, or bows to personalize your beret.

Q: Is this pattern suitable for beginners? A: Yes, this pattern is beginner-friendly. It's a great project for those who are new to crochet and want to practice basic stitches and techniques.